Short answer: to print multi-colour models on a Bambu Lab printer you need an AMS unit matched to your machine — the AMS Lite for the A1 series or the AMS 2 Pro for P, X and H series — plus the colour painting tools in Bambu Studio. Keep every slot loaded with the same material family (PLA is by far the easiest and has the widest colour range), and tune your flushing volumes so purge waste doesn't eat your spools. This guide walks through the whole workflow, from hardware to slicer settings to waste reduction, the way we run it on our own demo machines every day in Sydney.
How AMS multi-colour printing actually works
An AMS doesn't blend colours — it swaps them. Each time the model changes colour, the printer retracts the current filament all the way back to the AMS, feeds in the next spool, then purges the old colour out of the nozzle before continuing. That purge happens into a prime tower (the sacrificial block printed beside your model) and sometimes into the model's infill. Understanding this one mechanic explains almost everything about multi-colour printing: why it uses more filament, why it's slower, and why colour order matters.
It also explains the golden rule: every filament in a multi-colour print must share the same nozzle and bed temperature range. The printer can't re-tune temperatures mid-layer, so you can't mix PLA at 190–220 °C with a material that wants 250 °C in the same body. Stick to one material family per print — ideally one brand and line, so colour changes behave identically.
Which AMS fits your printer?
Bambu Lab's ecosystem has three current filament systems, and they are not interchangeable:
- AMS Lite — the open four-slot unit for the A1 and A1 Mini. Four colours per unit.
- AMS 2 Pro — the enclosed four-slot unit with built-in drying for the P1, P2S, X and H2 series. Up to four units can be chained for 16-colour prints.
- AMS HT — a single-slot, high-temperature drying unit. It's brilliant for engineering filaments and soft TPU, but with one slot it isn't a multi-colour device on its own; it pairs with AMS 2 Pro units in a mixed setup.
If you're still choosing hardware, our AMS Lite vs AMS 2 Pro comparison and AMS 2 Pro vs AMS HT guide cover the decision in detail, and the AMS setup guide covers unboxing, loading and firmware pairing step by step.
Setting up a multi-colour print in Bambu Studio
1. Map your AMS slots
With the AMS connected, Bambu Studio reads each slot automatically if you're using Bambu filament with RFID tags. For third-party spools in the AMS, set the material type and colour manually in the device panel — the slicer uses this to calculate purge volumes, so don't leave slots on defaults.
2. Paint or assign colours
There are two ways to make a model multi-coloured. For models designed as separate parts (most multi-colour files from model libraries), right-click each object or part and assign it a filament. For single-body models, use the colour painting tool (keyboard shortcut N): the sphere and fill-by-angle brushes handle organic shapes, while the height-range and fill-by-colour tools are faster for text, logos and layered signs.
3. Check flushing volumes before you slice
Open the flushing volumes matrix (the droplet icon next to the filament list). Bambu Studio estimates how much filament must be purged for each colour pair — flushing dark red into white needs far more than white into dark red. Two settings matter most: the flush multiplier (drop it to 0.6–0.8 once your transitions look clean) and “flush into objects' infill”, which hides purge material inside the model instead of wasting it on the tower.
4. Slice and sanity-check
The preview shows every filament change as a vertical line on the slider. Check the estimated filament usage panel: it breaks out model vs flushed vs tower weight, which tells you exactly what a tweak saved.
Choosing filament: why PLA dominates multi-colour work
PLA is the easiest material to print and the easiest to tune — and nowhere is that more valuable than multi-colour printing, where every colour change is another chance for a blob or a jam. It also has, by a huge margin, the richest variant and colour ecosystem of any material: basic, matte, silk, metallic, sparkle, glow, wood-filled, galaxy and gradient lines all slot straight into an AMS. Our Bambu Lab PLA variants guide maps the whole family, and the BIQU PLA range guide covers the Aura Silk and Translucent lines if you want more colour options on a budget.
A few practical picks from what we print with daily:
- PLA Basic — the reference multi-colour material. Boring, consistent, perfect.
- PLA Matte — hides layer lines and makes flat colour sections look injection-moulded; see our PLA Matte review.
- PLA Silk Multi-Color and PLA Basic Gradient — these shift colour along the spool itself, so a single slot produces rainbow effects with zero purge waste. Combine one with painted accents for the best of both.
One caution on mixing finishes: silk and matte PLA purge differently and bond slightly differently than basic PLA. It works, but run the first print with default flush multipliers before you start trimming them.
What about TPU in the AMS?
Only one flexible filament is approved to run through a standard AMS: TPU for AMS, which at Shore 68D is a semi-rigid material stiff enough to survive the feed path. Softer grades like 95A or 85A will buckle in a four-slot AMS — they belong in an AMS HT or external spool holder instead. If hardness grades are new to you, our TPU Shore hardness guide explains the whole ladder.
Cutting purge waste: the settings that matter
Multi-colour prints can flush 30 % or more of their filament on default settings. In rough order of impact:
- Flush into infill and objects. Free savings on any model with meaningful infill — purge hides inside where nobody sees it.
- Reduce colour changes per layer. A model painted with four colours on every layer swaps constantly; the same design with colours separated by height might swap a handful of times total. Design with colour zones where you can.
- Lower the flush multiplier gradually. Default is conservative. Step down towards 0.6 and stop when you see colour bleed.
- Order colours light to dark where the model allows — purging white into black is nearly free; black into white is expensive.
- Shrink the prime tower width once transitions are reliable, but never delete it: it's also where the nozzle re-pressurises after each swap.
Keeping multi-colour prints reliable
Every filament swap is a retraction, a cut and a re-feed, so small problems multiply. Three habits prevent most failures. First, dry filament matters double: along the Australian coast, ambient humidity sits at 60–80 % for much of the year, and damp PLA both strings more and purges less cleanly — our filament storage guide covers drying and dry boxes. Second, print PLA in its happy window (190–220 °C nozzle, 50–60 °C bed) rather than chasing speed with higher temperatures, which worsens stringing during swaps — the stringing guide has the full tuning routine. Third, keep the cutter and extruder clean; if swaps start failing mid-print, work through the clogged nozzle guide and check the first layer basics in our first layer adhesion guide.
Quick reference
| Setting | Recommended for multi-colour PLA |
|---|---|
| Nozzle temperature | 190–220 °C (same for every slot) |
| Bed temperature | 50–60 °C |
| Flush multiplier | Start 1.0, tune down to 0.6–0.8 |
| Flush into infill/objects | On |
| Prime tower | On, reduce width after first clean print |
| Max colours | 4 (one AMS) / 16 (4× AMS 2 Pro on P, X, H2 series) |
FAQ
Can I mix PLA and PETG in the same multi-colour print?
Not within one solid body — their temperature ranges don't overlap enough, and the layers won't bond properly. The one useful exception: because they don't stick to each other, PETG can be used as a support interface under PLA (and vice versa) for perfectly clean support-side surfaces. Assign it only to support layers, never to the model.
How many colours can a Bambu Lab printer handle in one print?
Four with a single AMS Lite or AMS 2 Pro. On the P, X and H2 series you can chain up to four AMS 2 Pro units for 16 colours in one job; the A1 series tops out at one AMS Lite.
Do multi-colour filaments like Silk Multi-Color work without an AMS?
Yes — that's their whole appeal. Silk Multi-Color and Gradient PLA shift colour along the length of the spool, so a single-spool printer with no AMS still produces striking colour-shift prints with zero purge waste. You just can't control where each colour lands.
Why is my multi-colour print using so much filament?
Check the slicer's filament breakdown after slicing: if "flushed" rivals the model weight, your design changes colour too often per layer or your flush multiplier is still at default. Flushing into infill and restructuring colours by height usually halves waste on the first pass.
Can the AMS feed flexible TPU for multi-material prints?
Only TPU for AMS (Shore 68D, semi-rigid). Softer TPU grades must bypass the four-slot AMS entirely — use an AMS HT or external spool — so true soft-flexible multi-colour isn't practical on a single-nozzle machine.
Ready to go full colour? Browse our filament range and Bambu Lab printers and AMS units — all stocked locally in Regents Park, Sydney, with fast Australia-wide shipping from an authorised Bambu Lab reseller and Australia's authorised Bambu Lab service centre. Comparing budgets? See the Bambu Lab price list for Australia, or get in touch — we print every day and we're happy to talk through your setup.
