Short answer: you don't actually choose between these two — your printer does. The AMS Lite only works with the open-frame A1 series, while the AMS 2 Pro serves the enclosed P1, P2, X and H-series machines. The real decision is which printer ecosystem you're buying into — and in humid coastal Australia, the AMS 2 Pro's built-in filament drying is a bigger deal than most spec sheets suggest.
Two systems, two different printer families
Bambu Lab's multi-colour systems look similar in photos — both hold four spools and feed them automatically — but they're built for different machines and aren't cross-compatible in either direction.
The AMS Lite is the open design that pairs with the A1 Mini and A1. Spools sit exposed on four arms, which keeps it light, easy to load and easy to see at a glance. You can buy it bundled from the start with the A1 Mini Combo or A1 Combo, which is how most A1 owners get theirs.
The AMS 2 Pro is the sealed, second-generation successor to the original AMS, and it connects to the enclosed CoreXY machines: P1S, P2S, X-series and the H2 family such as the H2S. If you're still weighing up which side of that fence to sit on, start with our A1 vs P1S comparison.
What the AMS 2 Pro actually adds
Over the original AMS, the 2 Pro's headline upgrade is active filament drying: it heats and circulates air inside the sealed enclosure, so it can dry spools in place and keep them dry while you print. It also brings a redesigned feed path that's gentler on filament and easier to clear, plus refreshed electronics for RFID reading of Bambu spools.
Why we keep banging on about drying: most Australians live on the coast at 60–80% relative humidity, and hygroscopic filaments drink that in within days. Wet filament strings, pops and prints weak. An AMS 2 Pro quietly solves the storage problem for the four spools you use most — for everything else, our guide to storing filament in Australia covers dry boxes and dryers.
The AMS Lite, being open to the air, dries nothing — in a humid room your spools sit exposed. A1 owners aren't doomed; they just need to handle drying and storage separately, and print moisture-sensitive materials reasonably soon after opening.
Materials: where each system earns its keep
The honest material split follows the printers, not the AMS units. An AMS Lite on an open-frame A1 is in its element with PLA in all its many variants and with PETG Basic — which, for the record, is the best strength-per-dollar choice on an open-frame machine, a point most multi-colour guides skip entirely (full comparison here).
The AMS 2 Pro's enclosed hosts unlock the warm-chamber materials: ABS, and critically for Australia, UV-resistant ASA for anything living outdoors under our sun. The 2 Pro's drying also matters most for exactly these engineering filaments, which are fussier about moisture than PLA. (Serious carbon-fibre materials like PAHT-CF have their own rules — see the carbon fibre filament guide.)
The TPU rule: one filament to remember
Flexible filament is where every AMS conversation gets caught out. The only TPU that can run through a standard AMS of any kind — AMS Lite or AMS 2 Pro — is Bambu Lab TPU for AMS, which at Shore 68D is deliberately semi-rigid so it won't buckle in the feed path. Softer TPUs must bypass the AMS: TPU 95A HF and softer grades feed externally, ideally with the TPU Feed Assist Module on compatible enclosed machines, or via the dedicated TPU path on the AMS HT. If Shore hardness numbers are new to you, our TPU Shore hardness guide decodes the whole 68D/95A/85A ladder.
Side-by-side
| AMS Lite | AMS 2 Pro | |
|---|---|---|
| Works with | A1 Mini, A1 (open-frame) | P1S, P2S, X-series, H2 series (enclosed) |
| Spool capacity | 4 | 4 |
| Enclosure | Open — spools exposed | Sealed |
| Filament drying | None | Active drying, works while printing |
| Best-fit materials | PLA family, PETG | PLA, PETG, ABS, ASA + engineering filaments |
| TPU through it | TPU for AMS (68D) only | TPU for AMS (68D) only |
| Expansion | One unit per A1-series printer | Stack up to four units via the AMS Hub — 16 slots |
So which should you buy?
Buying your first printer? Decide on the printer, and the AMS decision makes itself. A1 Mini or A1 for easy multi-colour PLA work on a budget; P1S or P2S if ABS, ASA or serious part strength is anywhere in your future. Current pricing for every combo lives on our Bambu Lab price list for Australia — combos are consistently the better value than adding an AMS later.
Already own a P1S with the original AMS? The upgrade case for the 2 Pro is strongest if you print engineering filaments in a humid area, or you're expanding to a multi-AMS setup anyway. If your AMS works and you mostly print PLA, a dry box is the cheaper fix. And if you're choosing between the 2 Pro and the AMS HT for a drying-capable add-on, we've written up AMS 2 Pro vs AMS HT separately.
First time setting any of these up? The AMS setup guide walks through loading, slot mapping and Bambu Studio settings. Bambu Lab's official wiki has the firmware-level details.
FAQ
Can I use the AMS Lite on a P1S or P2S?
No. The AMS Lite only connects to the A1 series. Enclosed printers like the P1S and P2S use the AMS, AMS 2 Pro or AMS HT.
Does the AMS 2 Pro work with the Bambu Lab A1 or A1 Mini?
No — the A1 series pairs exclusively with the AMS Lite. There's no adapter or workaround; the feed systems are physically different.
Can the AMS 2 Pro dry filament while printing?
Yes. Its active drying runs during prints, which is its biggest practical advantage over both the original AMS and the AMS Lite — especially in Australia's coastal humidity.
Can I print TPU through an AMS Lite or AMS 2 Pro?
Only Bambu Lab TPU for AMS (Shore 68D), which is semi-rigid by design. Softer TPUs like 95A or 85A must feed from outside the AMS, with the TPU Feed Assist Module or the AMS HT's dedicated TPU path.
How many spools can each system run?
Both hold four spools. The difference is expansion: enclosed printers can stack up to four AMS or AMS 2 Pro units through the AMS Hub for 16 slots, while an A1-series printer runs a single AMS Lite.
Buy it locally, set it up once
3D BRO is an authorised Bambu Lab reseller and Australia's authorised Bambu Lab service centre. Every AMS variant ships from Sydney stock in Regents Park with fast Australia-wide shipping — and because we print every day, we can tell you exactly how each one behaves before you buy. Browse the full Bambu Lab range, grab spools from the filament collection, or see why Australians buy Bambu Lab from 3D BRO.
