Skip to content
(02) 9772 4315 Mon to Fri, 9.30am - 5pm
Chatswood 0455 026 864 Open 7 days
0
🔥 Black Friday: save up to A$430 on 3D printers
Bambu Lab Calibration Guide: Bed Levelling, Flow & Pressure Advance

Bambu Lab Calibration Guide: Bed Levelling, Flow & Pressure Advance

Short answer: Bambu Lab printers handle bed levelling automatically before every print, so you never touch a levelling screw — but flow rate and flow dynamics (pressure advance) calibration are still on you, and they're what separate a good print from a great one. Run flow calibration once per new filament, keep your plate clean and your filament dry, and the machine does the rest. Here's exactly which calibrations matter, which are automatic on which model, and when to re-run them.

Why calibration still matters on an "auto-everything" printer

Every printer in the Bambu Lab range — from the A1 Mini to the H2 series — probes the build plate before each print and compensates for any tilt or unevenness in software. That's why there are no levelling knobs under the bed. But auto bed levelling only solves geometry. It can't fix a plate with fingerprint grease on it, filament that's absorbed a week of Sydney humidity, or a flow rate that's 8% off for the roll you just loaded. Those are calibration jobs too, and they're the ones most new owners skip.

As Australia's authorised Bambu Lab service centre, we see the pattern weekly: a printer comes into our Regents Park workshop "needing repair", and what it actually needs is a cleaned plate, dried filament and a two-minute flow calibration. This guide covers the full stack, roughly in the order that problems actually occur.

1. Auto bed levelling: what it does — and what it can't

At the start of each job the printer probes a mesh of points across the plate and builds a height map, then adjusts the Z height continuously as the first layer goes down. You can toggle this per print in Bambu Studio, but leave it on; the 60 seconds it costs is cheaper than a failed first layer.

When the first layer is still patchy after auto levelling, the cause is almost always one of these:

  • A dirty plate. Wash your Textured PEI plate with warm water and dish soap — isopropyl alcohol alone just spreads the oils around. Our first layer adhesion guide covers the full cleaning routine per plate type.
  • The wrong plate selected in Bambu Studio. A Cool Plate SuperTack and a Smooth PEI plate run different bed temperatures; printing with the wrong profile selected sabotages adhesion even on a perfectly levelled bed.
  • Debris on the nozzle. The printer probes with the nozzle tip on several models, so a blob of carbonised filament skews the whole height map. If the blob keeps returning, you may be heading toward a partial clog — see how to fix a clogged nozzle.
  • A genuinely damaged plate or worn surface. PEI sheets wear out with use. If prints only fail in one zone of the plate, that zone's coating is usually the culprit.

2. Flow rate calibration: once per filament, two minutes, biggest payoff

Flow rate tells the printer how much plastic actually comes out per millimetre of filament pushed. It varies between brands, between materials, and even between colours of the same line — a PLA Basic and a silk PLA can be several percent apart. Symptoms of flow being off: rough or bulging top surfaces (over-extrusion) or pinholes and weak walls (under-extrusion).

In Bambu Studio, select your filament, open Calibration, and run the flow rate test: the printer prints a set of patches, you pick the smoothest one, and the correction saves into that filament's profile. Do it once for every new filament you load — especially third-party rolls, since Bambu's own profiles are tuned for Bambu filament. If you're unsure which material to start tuning with, our PLA vs PETG guide and the PLA variants guide are the sensible reading order.

3. Flow dynamics calibration (the K value / pressure advance)

Flow dynamics — the K value — compensates for pressure building up in the nozzle during acceleration. Wrong K values show up as bulged corners, gaps after corners, and inconsistent seam quality. On the A1 series and the newer X2D and H2-class machines, the printer calibrates this automatically using onboard sensors. On a P1S, run the manual Flow Dynamics test in Bambu Studio: it prints a series of lines, you pick the one with the most even width, and the K value saves to the filament profile.

K values are per-filament, not per-printer. A flexible filament like TPU 95A HF needs a completely different K value than a rigid PLA — one more reason to calibrate per roll rather than copying numbers off the internet. If you're seeing fine hairs between parts rather than corner defects, that's a retraction problem, not a K value problem: see fixing stringing on Bambu Lab printers.

4. Belt tension and the mechanical side

Calibration can't compensate for loose hardware. The A1 series tensions its belts automatically, but on a P1S it's a periodic manual job — ringing or ghosting on flat surfaces is the classic symptom, and a belt tension tool takes the guesswork out of it. While you're in there, follow the lubrication schedule in our Bambu Lab maintenance guide; dry rails cause artefacts that look exactly like calibration faults.

Hotends are consumables too. A worn or scarred nozzle extrudes inconsistently no matter how well-calibrated the profile is. Replacements are cheap and tool-free to swap — we keep A1-series hotends and P1-series complete hotends in stock in Sydney. After any nozzle or hotend change, re-run your calibrations: the melt zone geometry has changed.

5. The Australian step everyone skips: dry your filament first

Here's the thing about calibrating in Australia: most of our population lives on the coast at 60–80% relative humidity, and filament absorbs moisture fast. Wet filament extrudes differently — it foams microscopically, changing effective flow — so a flow calibration run on damp filament is a calibration of damp filament, and the numbers go stale the moment you dry it. Dry first, then calibrate. Our guide to storing and drying filament in Australia covers dryers, dry boxes and which materials are most hygroscopic.

Temperature quick reference

Calibrate at the temperature you'll actually print at. These are the working ranges we use every day in the workshop:

Material Nozzle Bed Notes
PLA 190–220°C 50–60°C Easiest to calibrate; start here
PETG 230–250°C 70–80°C Expect more stringing during tests — normal
ABS / ASA 240–270°C 90–100°C Enclosed printer; watch for warping
TPU 220–240°C Ambient–low Slow speeds; calibrate flow gently

When to recalibrate: the honest schedule

Event Bed levelling Flow rate Flow dynamics (K)
Every print Automatic — —
New filament brand/line — Yes Yes
Nozzle or hotend swap Automatic next print Yes Yes
After drying wet filament — Re-check —
Printer moved/transported Automatic next print — —
Ghosting/ringing appears — — Check belts first

For the deeper engineering background on each calibration routine, Bambu Lab's official wiki is worth bookmarking.

FAQ

How often should I calibrate my Bambu Lab printer?

Bed levelling runs automatically every print, so never. Flow rate and K value: once per new filament, and again after any nozzle or hotend change. There's no benefit to re-running calibrations on a schedule if nothing has changed.

Do I need to manually level the bed on a Bambu Lab A1?

No — there are no levelling screws on any current Bambu Lab printer. If the first layer is failing, the fix is a clean plate, dry filament or the correct plate profile in Bambu Studio, not levelling.

What is the K value on a Bambu Lab printer?

It's the pressure advance coefficient: a per-filament number that compensates for nozzle pressure lag during speed changes. Too low gives bulging corners; too high gives gaps after corners. It's stored in the filament profile, so each filament keeps its own.

Why is my first layer still bad after auto bed levelling?

In our workshop the ranking is: greasy plate (wash with dish soap, not just alcohol), wet filament, wrong plate profile selected, then a worn plate surface. Actual levelling faults are rare.

Does wet filament affect calibration?

Yes — moisture changes how the filament extrudes, so any flow calibration done on wet filament becomes wrong once the filament is dried. In coastal Australia, dry first, calibrate second.

Get it dialled in

3D BRO is an authorised Bambu Lab reseller and Australia's authorised Bambu Lab service centre, with Sydney stock in Regents Park and fast Australia-wide shipping. We print every day on the same machines we sell, so if a calibration problem has you stuck, bring it in or get in touch. Browse the full 3D printer range, stock up from the filament collection, check current printer and accessory pricing on our Bambu Lab price list, or read why locals buy Bambu Lab from 3D BRO.

Cart 0

Your cart is currently empty.

Start Shopping