Short answer: If the part will ever see sunlight, buy ASA — Australia has the strongest UV levels in the world, and ABS chalks, fades and goes brittle outdoors here within a season. For indoor functional parts, ABS Basic remains the best all-round performance-per-dollar material in FDM. Both need an enclosed printer such as the P1S or P2S, and both want ventilation.
Two siblings, one decisive difference
ABS and ASA are close relatives: similar strength, similar heat resistance, similar printing behaviour, and the same hardware demands. ABS is the original — the oldest FDM 3D printing material there is, refined over decades into the best balance of mechanical performance and price in the hobby. ASA is its weatherproof descendant: the butadiene rubber phase in ABS (the part UV destroys) is replaced with acrylate rubber, which shrugs off sunlight. The result is UV resistance plus weather resistance with almost no mechanical trade-off.
That one difference decides the whole comparison, and it matters more in Australia than almost anywhere else on earth. Our UV index regularly hits extreme levels that European and North American guides simply aren't written for — which is why we treat ASA not as a niche engineering material but as a staple every Australian printer owner should keep on the shelf. We've covered the science in our ASA UV guide for Australia.
Where ABS wins
Indoors, ABS is hard to argue with. Decades of industrial use mean its behaviour is thoroughly understood: good impact resistance, good heat tolerance (your PLA phone mount sagging on a summer dashboard is exactly what ABS was built to avoid), easy post-processing — it sands, glues and acetone-smooths beautifully — and it's typically the cheapest of the engineering materials. For workshop tools, brackets, enclosures, clips and anything that lives inside, Bambu Lab ABS Basic is the default we recommend. Rather than quote prices that date quickly, see the current Bambu Lab price list for Australia or the product page for today's pricing.
Where ASA wins
Everywhere the sun reaches. Letterbox parts, garden fittings, irrigation clips, camping and 4WD gear, roof-rack accessories, drone bodies, car exterior trim, boat hardware — in Australia these are ASA jobs, full stop. ASA keeps its colour and toughness after years outdoors where ABS visibly degrades in months. It also has slightly better moisture and weather stability overall, and its matte finish hides layer lines a touch better. If your use case list includes a single outdoor item, skip the decision entirely and stock ASA — it does everything ABS does indoors too.
Head-to-head
| ABS Basic | ASA | |
|---|---|---|
| UV / outdoor durability | Poor — fades and embrittles in Australian sun | Excellent — the reason it exists |
| Strength & impact | Very good | Very good (near-identical) |
| Heat resistance | Good | Good |
| Warping | Prone — enclosure essential | Slightly less prone, enclosure still essential |
| Post-processing | Excellent (acetone smoothing) | Good |
| Cost positioning | Cheapest engineering filament | Modest premium — see price list |
| Best for | Indoor functional parts, tools, prototypes | Anything outdoors, automotive, marine, camping |
What you need to print either
Both materials print at 240–270°C with a 90–100°C bed, and both shrink as they cool — which is why an enclosed chamber isn't a luxury but a requirement. On Bambu Lab hardware that means the P1S, P2S, X series or H2 series; our P1S vs P2S comparison walks through which enclosed machine fits your budget, and an official refurbished P1S Combo is a smart lower-cost path into enclosed printing (more in our refurbished Bambu Lab guide).
Ventilate the room — both materials emit styrene fumes while printing, so run the printer in a garage or near an open window rather than a bedroom. Keep the enclosure closed, use the textured plate with glue, and if corners still lift, our warping fix guide covers draft management and plate prep in detail. Store opened spools sealed with desiccant — Australian coastal humidity is unkind to every filament, and our storage guide shows the setup we use in the Sydney shop.
Printing on an open-frame A1? Choose neither
This is the decision point most guides skip: if you own an A1 or A1 Mini, don't fight ABS or ASA without an enclosure — warping and splitting will eat your filament and your patience. On an open-frame machine, PETG Basic is the best choice when you need high strength at a sensible price: it prints happily at 230–250°C with a 70–80°C bed, no chamber required. Our PLA vs PETG guide covers when to step up from PLA, and the broader Australian filament selection guide maps the whole decision tree.
Our recommendation
Stock both if you print functional parts regularly; if you're buying one spool, make it ASA in Australia. As an authorised Bambu Lab reseller and Australia's authorised Bambu Lab service centre, we print with both materials every day — both are in stock in Sydney (Regents Park) with fast Australia-wide shipping. Browse the filament collection, the full Bambu Lab range and our 3D printers, or read why buy Bambu Lab from 3D BRO.
FAQ
Can I print ABS or ASA on a Bambu Lab A1?
Not reliably — the A1 is open-frame, and both materials need a warm, draft-free chamber to avoid warping and layer splitting. On an A1, use PETG for strength; if you need ABS/ASA regularly, an enclosed P1S or P2S is the right upgrade.
Will ASA really not fade in the Australian sun?
ASA is formulated specifically to resist UV: parts keep their colour and toughness for years outdoors, where ABS visibly chalks within months under Australian UV levels. Darker colours mask any eventual change even longer.
Do I need ventilation to print ABS and ASA?
Yes. Both release styrene fumes during printing. Keep the enclosure closed during the print, run the printer in a ventilated space such as a garage, and let the chamber air out before opening it right after a print.
Is ASA harder to print than ABS?
No — if anything it's slightly easier, with marginally less warping. Same temperatures (240–270°C nozzle, 90–100°C bed), same enclosure requirement, same plate prep. If you can print ABS, you can print ASA with the same profile habits.
Questions about which material suits your project? Contact the 3D BRO team — we print every day and we're happy to help.
